|
Post by punisher on Aug 12, 2019 11:25:41 GMT -6
I did ad u suggested jacked it up took out the lines from the shocks. Seemed to work. But im definitely not hearing the compressor. Does the w002 4.o have the air dryer? On the compressor? I found one for $128. On ebay
|
|
|
Post by punisher on Aug 12, 2019 11:50:40 GMT -6
Tried as u suggested seemed to work. Thanks.
|
|
tigger
Administrator
Posts: 2,844
Staff Member
|
Post by tigger on Aug 12, 2019 14:12:35 GMT -6
Tried as u suggested seemed to work. Thanks. You're welcome! ...But im definitely not hearing the compressor. Does the w002 4.o have the air dryer? On the compressor? I found one for $128. On ebay Yes, it has an attached dryer. If it helps, the part number for the compressor assembly is GM#12494811 (or the superseded GM#22153457). Here's a diagram; If you want to test yours before you spend money on a new one; At the compressor connector with key OFF: 12V to Pin B (GREEN) and GROUND to Pin D (BLACK) - Compressor should run, shocks should inflate. 12V to Pin A (RED) and GROUND to Pin C (WHITE) - Exhaust solenoid valve should open, shocks should deflate. GL
|
|
|
Post by AuroraGirlFromMars on Sept 30, 2020 3:52:21 GMT -6
yes i have same thing i guess because its not Real scanner and china knock off it doesnt work .. Or maybe there is something else need to be done before steering thing will work on scanner. im back 2 years later. park avenue locks it out until all body codes are fixed. and certain engine ones, esp with EBTCM. figured id share, likely similar
|
|
|
Post by AuroraGirlFromMars on Sept 30, 2020 3:54:34 GMT -6
Tried as u suggested seemed to work. Thanks. You're welcome! ...But im definitely not hearing the compressor. Does the w002 4.o have the air dryer? On the compressor? I found one for $128. On ebay Yes, it has an attached dryer. If it helps, the part number for the compressor assembly is GM#12494811 (or the superseded GM#22153457). Here's a diagram; If you want to test yours before you spend money on a new one; At the compressor connector with key OFF: 12V to Pin B (GREEN) and GROUND to Pin D (BLACK) - Compressor should run, shocks should inflate. 12V to Pin A (RED) and GROUND to Pin C (WHITE) - Exhaust solenoid valve should open, shocks should deflate. GL Im back for you too. Does 1g have a different setup to 2001-03? Perhaps the same as park avenue(which it shares a lot of body and suspension) which have un-computerized diagnostics? Interfaceable to a scantool, that is. Adjustsments and diagnostics have to be done the old way? same compressor you think too?
|
|
Paulaurora
Super Moderator
Posts: 3,823
Staff Member
|
Post by Paulaurora on Oct 4, 2020 15:53:03 GMT -6
I know this probably isn't the right place to post this, but since this thread is in regards to shocks, I have 2 sets of ACDelco air shocks available for sale if interested. $50/set plus shipping from Iowa. repost this to the marketing section
|
|
RCA1186
Administrator
Rob
Go Pack Go!
Posts: 4,835
Staff Member
|
Post by RCA1186 on Oct 5, 2020 6:33:35 GMT -6
I know this probably isn't the right place to post this, but since this thread is in regards to shocks, I have 2 sets of ACDelco air shocks available for sale if interested. $50/set plus shipping from Iowa. repost this to the marketing section Post Has been moved to its own thread in Marketplace aurorah.proboards.com/thread/31928/air-shocks-sale
|
|