|
|
Post by osmo1102 on Nov 16, 2022 14:51:27 GMT -6
Bought a Actron CP9690 to scan my 1995 Aurora. Its got 3 codes that I am not quite sure what they mean, having a hard time finding answers online.
Code 1 - P0133 No ABS/TCS serial data
Code 2 - P0134 No IPC serial data
Code 3 - P0135 No HVAC serial data
Thanks ahead of time
|
|
RCA1186
Administrator 
Rob
Go Pack Go!
Posts: 4,808 
Staff Member
|
Post by RCA1186 on Nov 17, 2022 11:16:08 GMT -6
Sounds like possible communication issue with pcm if I had to guess. Might have lost a ground
|
|
|
|
Post by AuroraGirlFromMars on Nov 20, 2022 13:04:29 GMT -6
|
|
|
|
Post by osmo1102 on Nov 24, 2022 13:50:38 GMT -6
Not sure what anything in that picture means, but I read the codes again today and I came up with....
P0136 no DERM serial data
P0135 no HVAC serial data
P0134 no IPC serial data
P0133 no ABS/TCS serial data
P0123 refrigerant pressure too low
P0109 KAM checksum failed
P0052 PCM KAM checksum problem
P0080 throttle position idle speed control learning not done.
I'm thinking you're right with either a bad ground or bad PCM?
|
|
|
|
Post by osmo1102 on Nov 24, 2022 13:53:30 GMT -6
Not sure what anything in that picture means, but I read the codes again today and I came up with.... P0136 no DERM serial data P0135 no HVAC serial data P0134 no IPC serial data P0133 no ABS/TCS serial data P0123 refrigerant pressure too low P0109 KAM checksum failed P0052 PCM KAM checksum problem P0080 throttle position idle speed control learning not done. I'm thinking you're right with either a bad ground or bad PCM? I don't have a cat on my car. Maybe that's causing some? |
|
|
|
Post by AuroraGirlFromMars on Nov 24, 2022 17:49:58 GMT -6
Not sure what anything in that picture means, but I read the codes again today and I came up with.... P0136 no DERM serial data P0135 no HVAC serial data P0134 no IPC serial data P0133 no ABS/TCS serial data P0123 refrigerant pressure too low P0109 KAM checksum failed P0052 PCM KAM checksum problem P0080 throttle position idle speed control learning not done. I'm thinking you're right with either a bad ground or bad PCM? I don't have a cat on my car. Maybe that's causing some? your PRE cat converter location is what is bad. You have a 3.5 or a 4.0? The sensors bank 1 and 2, but sensor 1 is always going to be before cat. The bank is not important so much as the position. once you know its before it, and you have no cat, Id say your o2 is bad or the exhaust is not equipped with one. you should find and see if you can find your o2 sensors BEFORE the cat original spot. Then, follow the wires on it |
|
|
|
Post by osmo1102 on Nov 28, 2022 6:00:28 GMT -6
I have the 4.0L I will definitely check the o2 sensors before the cat. I appreciate the help and will keep you informed. Thanks!
|
|
|
|
Post by AuroraGirlFromMars on Dec 2, 2022 9:23:57 GMT -6
I have the 4.0L I will definitely check the o2 sensors before the cat. I appreciate the help and will keep you informed. Thanks! I could be wrong but if I recall correctly the O2 before the cat are located down by the oil pan where each manifold goes its way. im not confident on that but i feel like thats where |
|
